| Solaris |
|
|
Getting Started
Getting Started With Crossbow
Pre-requisites
- Solaris Nevada build 81 or Solaris Express Developer Release
- Nemo-compliant networking card(bge, e1000g, xge, nxge, ...)
- bfu and acr scripts
- Solaris Networking Virtualization bfu archives
Table of Contents
- Virtualizing the Networking Devices
- Bandwidth Management
- IP Instances, Exclusive Zones
- CPU Resources with Network Virtualization
Virtualizing the Networking Devices
A single physical networking card is presented as multiple virtual cards,
which are called vnics.
A vnic acts like any networking device. It has its own MAC address.
An IP interface may be plumbed over a vnic, which can then be
assigned an IPv4 or IPv6 address.
Example:
- List the physical links on the system:
# dladm show-link
bge0 type: non-vlan mtu: 1500 device: bge0
ath0 type: non-vlan mtu: 1500 device: ath0
- Create a virtual NIC over bge0:
# dladm create-vnic -l bge0 1
# dladm show-vnic
LINK OVER SPEED MACADDRESS MACADDRTYPE
vnic1 bge0 0 Mbps 2:8:20:22:51:dc random
Note that a random MAC address was automatically assigned to the VNIC. The VNIC and its MAC address will persist if the host is rebooted.
- A new data link is created:
# dladm show-link
bge0 type: non-vlan mtu: 1500 device: bge0
ath0 type: non-vlan mtu: 1500 device: ath0
vnic1 type: non-vlan mtu: 1500 device: vnic1
- Bring up an IP interface on vnic1:
# ifconfig vnic1 plumb
# ifconfig vnic1 dhcp start
# ifconfig vnic1
vnic1: flags=201004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4,CoS>
mtu 1500 index 4
inet 129.146.109.26 netmask fffffe00 broadcast 129.146.109.255
ether 2:8:20:22:51:dc
Now, the virtual NIC is visible to all classical network monitoring tools,
such as netstat(1M):
# netstat -ian
Name Mtu Net/Dest Address Ipkts Ierrs Opkts Oerrs Collis Queue
lo0 8232 127.0.0.0 127.0.0.1 1624 0 1624 0 0 0
lo0 8232 127.0.0.0 127.0.0.1 0 N/A 1618 N/A N/A 0
ath0 1500 10.192.0.0 10.192.11.51 19036 0 3857 0 0 0
ath0 1500 10.192.0.0 10.192.11.51 17468 N/A 3805 N/A N/A 0
vnic1 1500 129.146.108.0 129.146.109.26 371 0 12 0 0 0
vnic1 1500 129.146.108.0 129.146.109.26 10 N/A 3 N/A N/A 0
Bandwidth Management
The bandwidth may be limited for a whole VNIC by specifying the
maxbw property (expressed in Mbps) when the vnic is created:
# dladm create-vnic -l bge0 -p maxbw=15 3
# dladm show-vnic
LINK OVER SPEED MACADDRESS MACADDRTYPE
vnic1 bge0 0 Mbps 2:8:20:22:51:dc random
vnic3 bge0 0 Mbps 2:8:20:41:c2:71 random
# dladm show-linkprop -p maxbw vnic3
LINK PROPERTY VALUE DEFAULT POSSIBLE
vnic3 maxbw 15 ~-- ~--
A bandwidth limit can also be set on an existing data-link such as a physical NIC or an existing VNIC:
# dladm set-linkprop -p maxbw=300 bge0
# dladm show-linkprop -p maxbw bge0
LINK PROPERTY VALUE DEFAULT POSSIBLE
bge0 maxbw 300 ~-- ~--
A finer grain limit could be set on a per-transport or on a per-protocol
basis, on top of any data-link.
For that we use the new command flowadm(1m) to create a new flow of
packets defined by the description of the packets matching the flow
(transport, local_port, etc ...). The limit on the bandwidth that can
be used by that flow is specified using the maxbw flow property.
# flowadm add-flow -l vnic2 -a transport=tcp tcp~_flow
# flowadm set-flowprop -p maxbw=100 tcp~_flow
# flowadm show-flow
flow name flow attributes policy attributes
tcp~_flow v4:tcp (L) 100 Mbps
Incoming and outgoing TCP packets will be subject to a maximum of
100Mbps of throughput. Other traffic will use all remaining bandwidth
available for vnic1.
We can observe the accumulated statistics about the packets used by
the tcp_flow, by running kstat in the global zone:
bash-3.00# kstat -n tcp_flow
module: unix instance: 0
name: tcp_flow class: flow
crtime 29.903360333
ierrors 0
ipackets 10177
obytes 0
oerrors 0
opackets 0
rbytes 550094
snaptime 17969.794047786
Per-flow bandwidth utilization may also be monitored in real time
by invoking netstat -K.
In our example with tcp_flow, this is a snapshot of the real-time
output screen, while running netperf between
two zones, one attached to vnic1 and the other to vnic2:
Flow Link iKb/s oKb/s iPk/s oPk/s
vnic1 bge0 106236.18 534.43 9068.56 1266.79
vnic2 bge0 534.89 106235.75 1267.78 9067.58
vnic3 bge0 0.46 0.00 0.98 0.00
vnic4 bge0 0.46 0.00 0.98 0.00
tcp_flow vnic2 428.95 0.00 1016.77 0.00
Totals 13400.12 13346.27 11355.07 10334.38
IP Instances and Zones
A zone with an exclusive IP stack has its own instance of the global tables
and variables used in the TCP/IP stack. This allows a zone to be connected to
a separate LAN or VLAN without sharing any networking state or policies with
other zones.
The zone with its exclusive IP instance has its own IP routing table,
ARP table, IPsec policies and security associations, IP Filter rules,
TCP/IP ndd tunables, etc.
To create a zone with an exclusive IP instance,
set ip-type=exclusive in zonecfg(1M).
Since an exclusive zone has control over its ARP and IP internal structures,
an IP address does not need to be set for the zone by the global zone
administrator any more.
Simply pick a physical interface to be assigned to the zone,
or specify a VNIC which you previously created using dladm(1M).
The following is a sample of zonecfg input:
create -b
set zonepath=/export/home/Zones/z3
set autoboot=false
set ip-type=exclusive
add inherit-pkg-dir
set dir=/lib
end
add inherit-pkg-dir
set dir=/platform
end
add inherit-pkg-dir
set dir=/sbin
end
add inherit-pkg-dir
set dir=/usr
end
add inherit-pkg-dir
set dir=/opt
end
add inherit-pkg-dir
set dir=/etc/crypto
end
add net
set physical=vnic3
end
Copy it into a file (e.g. /var/tmp/zcfg.in).
Then run:
# zonecfg -z z3 -f /var/tmp/zcfg.in
(Note: the following output is normal)
z3: No such zone configured
Use 'create' to begin configuring a new zone.
zoneadm will now show the newly created zone 'z3' in a configured state:
# zoneadm list -cv
ID NAME STATUS PATH BRAND IP
0 global running / native shared
1 z1 running /export/home/Zones/z1 native excl
2 z2 running /export/home/Zones/z2 native excl
\- z3 configured /export/home/Zones/z3 native excl
Note the 'excl' under the 'IP' column indicating an exclusive IP instance for
the zone z3.
The zone needs to be installed:
bash-3.00# zoneadm -z z3 install
Note: depending on the CPU speed, the installation may take around 10 minutes.
bash-3.00# zoneadm list -cv
ID NAME STATUS PATH BRAND IP
0 global running / native shared
1 z1 running /export/home/Zones/z1 native excl
2 z2 running /export/home/Zones/z2 native excl
\- z3 installed /export/home/Zones/z3 native excl
Boot the zone:
bash-3.00\# zoneadm -z z3 boot
and connect to the zone's console by running zlogin -C z3, and initialize the
naming services. You will have the usual interactive post installation dialog,
set the hostname (zone's name), the time zone, the zone's root password, etc ..
The zone is now ready.
You may bring up the network on the zone:
z3 console login: root
Password:
Feb 15 10:43:55 z3 login: ROOT LOGIN /dev/console
Sun Microsystems Inc. SunOS 5.11 snv_55 October 2007
#
# zonename
z3
#
# ifconfig -a plumb
# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
vnic3: flags=201000842<BROADCAST,RUNNING,MULTICAST,IPv4,CoS> mtu 1500 index 2
inet 0.0.0.0 netmask 0
ether 2:8:20:41:c2:71
Note: dladm show-link cannot yet be run from a non global zone. However, ifconfig -a will plumb all non loopback interfaces that were assigned to the zone by the global zone administrator.
# ifconfig vnic3 1.1.1.3/24 up
# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
vnic3: flags=201000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4,CoS> mtu 1500 index 2
inet 1.1.1.3 netmask ffffff00 broadcast 1.1.1.255
ether 2:8:20:41:c2:71
# netstat -rn
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
------------
1.1.1.0 1.1.1.3 U 1 1 vnic3
224.0.0.0 127.0.0.1 U 1 0 lo0
127.0.0.1 127.0.0.1 UH 1 36 lo0
The zone can now communicate with other hosts on the network.
# ping 1.1.1.1
1.1.1.1 is alive
Note:
Just like a single zoned system, /etc/hostname.vnic3 or /etc/dhcp.vnic3 can
be used to have the network automatically initialized with a static or dynamic
IP address upon reboot of the zone.
Back to the global zone:
bash-3.00# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
ath0: flags=201004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4,CoS> mtu 1500 index 3
inet 192.168.1.132 netmask ffffff00 broadcast 192.168.1.255
ether 0:b:6b:4d:b1:4
bash-3.00#
bash-3.00# netstat -rn
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
------------
default 192.168.1.1 UG 1 45 ath0
192.168.1.0 192.168.1.132 U 1 4 ath0
224.0.0.0 192.168.1.132 U 1 0 ath0
127.0.0.1 127.0.0.1 UH 2 68 lo0
The IP interface 'vnic3' is not exposed to the global zone, or other
zones.
Further details about IP instances may be found in the Presentation to OpenSolaris User Group
and the IP instances Architecture.
CPU Resources with Network Virtualization
NICs and VNICs may be bound to a subset of the processors available on a
system. When such binding is established, most of the packet processing will be executed on the bound CPUs.
This feature is particularly useful for deeper separation of the CPU resources
between zones and containers. It extends that separation to account for most
of the CPU cycles spent anonymously in the networking subsystem on behalf of
a zone.
The example below illustrates a setup that shows the difference
in CPU utilization when this feature is in use.
The NIC will still interrupt a system defined CPU(s), which are currently
not under the virtualization control. However, incoming packets are
quickly dispatched to be processed by a CPU from the zone's processor set.
The instructions for creating a CPU resource pool with 4 CPUs out of a T-10000 multi-core system are described here
Configure a zone work1zone with an exclusive IP stack, and connect it to a
vnic called vnic1, as described above. (In this example, we
use vnic1 over bge1, which was assigned by the system to interrupt the CPU 8).
Assign the work1-pool pool to work1zone:
# zonecfg -z work1zone set pool=work1-pool
Reboot work1zone so that it binds to the new pool:
# zlogin work1zone init 6
Running iperf between the work1zone
container and an external host, will actually show that
processors 4-7 are mainly used. Most CPUs outside that set are occasionally
used at a 5% or less of the time, for other internal load.
This is the expected behavior because the application (and all its system
calls) are actually hosted by the container.
CPU minf mjf xcal intr ithr csw icsw migr smtx srw syscl usr sys wt idl
0 0 0 106 277 175 0 0 0 2 0 0 0 1 0 99
1 0 0 0 1 0 0 0 0 0 0 0 0 0 0 100
2 0 0 0 1 0 0 0 0 0 0 0 0 0 0 100
3 0 0 0 1 0 0 0 0 0 0 0 0 0 0 100
4 0 0 0 3765 0 7496 7 76 355 0 4556 2 19 0 79
5 0 0 0 3590 0 7175 7 77 336 0 4310 2 19 0 80
6 0 0 0 1504 0 3009 3 15 137 0 1912 1 8 0 92
7 0 0 0 1108 8 2196 1 6 91 0 1394 1 6 0 94
8 0 0 7247 7711 7706 9 0 0 860 0 0 0 56 0 44
...
22 0 0 9114 6688 0 13659 0 0 1176 0 0 0 64 0 36
23 0 0 0 3 0 5 0 0 0 0 1 0 0 0 100
CPU # 22 was being used at 64% of the time, all inside the
system. That is the cost of processing incoming packets for work1zone.
That cost is being charged to a CPU that is not member of the processor set
that the container is assigned to.
To minimize the unfair utilization of CPU resources induced by work1zone
inbound traffic, vnic1 needs to be also "bound" to the CPUs of
work1-pset:
From the global zone, run:
# dladm set-linkprop -p cpus=4,5,6,7 vnic1
A second experiment with iperf shows:
CPU minf mjf xcal intr ithr csw icsw migr smtx srw syscl usr sys wt idl
0 0 0 118 270 168 0 0 0 1 0 0 0 0 0 100
1 0 0 0 1 0 0 0 0 0 0 0 0 0 0 100
2 0 0 0 1 0 0 0 0 0 0 0 0 0 0 100
3 0 0 0 1 0 0 0 0 0 0 0 0 0 0 100
4 0 0 2370 4477 0 9045 30 95 623 0 2799 1 33 0 66
5 0 0 2702 4630 0 9366 26 88 608 0 2331 1 32 0 67
6 0 0 2995 4459 0 9017 27 83 737 0 1778 1 34 0 65
7 0 0 0 3225 5 6491 3 51 167 0 4494 2 20 0 79
8 0 0 7574 7587 7574 26 0 1 2767 0 5 0 51 0 49
...
22 0 0 1243 1088 0 2175 0 0 344 0 4 0 2 0 98
23 0 0 2 8 0 15 0 0 1 0 0 0 0 0 100
Note in particular:
. CPUs 4-7 idle time decreased, and their sys time has increased since
they work more to handle work1zone's packets.
. CPU #22 is barely working at 2% instead of the previous 64%.
Terms of Use
|
Privacy
|
Trademarks
|
Copyright Policy
|
Site Guidelines
|
Site Map
|
Help
Your use of this web site or any of its content or software indicates your agreement to be bound by these Terms of Use.
© 2012, Oracle Corporation and/or its affiliates.